The TOPEP replacement for HYDAC 0060D005BH4HC is a 5-micron glass-fibre hydraulic filter element for compatible pressure-line filter assemblies. It helps control particulate contamination in oil supplied to sensitive downstream components. The element measures 47 mm outside diameter, 22.1 mm inside diameter and 84 mm overall height.
Select the replacement against the housing drawing, fluid compatibility and operating requirements. This is a TOPEP aftermarket replacement, not a genuine HYDAC product.
| Product Type | Replacement hydraulic pressure filter element |
| Replacement Reference | HYDAC 0060D005BH4HC |
| Spaced Reference Format | 0060 D 005 BH4HC |
| Supplier Brand | TOPEP |
| Filter Media | Glass fibre |
| Filtration Rating | 5 µm |
| Outside Diameter | 47 mm |
| Inside Diameter | 22.1 mm |
| Overall Height | 84 mm |
| Intended Filter Position | Pressure line, subject to housing and application confirmation |
The specified 5-micron glass-fibre media provides a fine-filtration option for hydraulic oil cleanliness requirements. Particle control matters where contamination can contribute to valve sticking and component wear. Select the required efficiency using test data as well as the micron designation.
In a correctly selected pressure-line assembly, the element filters oil on its way to downstream valves, actuators or motors. This places filtration at the delivery side of the circuit rather than relying solely on reservoir cleanliness.
The 47 mm diameter and 84 mm height provide a compact cartridge envelope for matching housings. This is useful when servicing machinery where installation space is fixed. End-cap geometry and sealing interfaces must also match; size alone does not prove interchangeability.
When the existing housing is compatible and serviceable, maintenance replaces the element while retaining the housing. Inspect the sealing surfaces and housing condition during servicing to preserve correct installation and prevent unintended internal leakage.
Relevant application areas for compatible hydraulic pressure-filter installations include:
Machine tools and automated manufacturing: Hydraulic power units supplying clamping, positioning and actuation circuits, where particulate control supports consistent component operation.
Presses and plastics processing: Hydraulic control circuits on forming presses and injection-moulding equipment, subject to confirmation of the installed filter assembly and operating flow.
Construction and material handling: Compatible pressure-filter assemblies on mobile machinery, where changing loads, oil viscosity and pressure cycles must be considered during replacement selection.
These are relevant industry contexts, not a verified machine-fitment list. Confirm the housing and circuit requirements for each installation.
System working pressure and pressure difference across a filter element describe different loads. The housing contains the pressurised oil; the element must withstand the difference between its dirty and clean sides. A housing pressure rating cannot establish an element's collapse resistance.
HYDAC's published BH4HC reference literature specifies 170 bar collapse/burst pressure stability. This is original-series reference information, not a test certificate for the TOPEP replacement. A 210 bar system requirement must be checked against the complete assembly, and any requirement for 210 bar element differential-pressure resistance needs separate verification.
Also check the bypass arrangement and the clogging-indicator threshold. Collapse resistance is not a permissible service target: replace an element according to the equipment instructions, well before a structural limit is approached.
Our guide to identifying the right replacement filter element explains the additional fit and compatibility checks.
Submit the original element drawing or sample details for a replacement review. If a different seal, media grade or structural pressure requirement is needed, identify it in the inquiry so feasibility can be assessed before quotation. Changes are subject to technical confirmation.
Q1: Can this glass-fibre element be cleaned and reused?
Treat it as a replacement consumable. No reusable cleaning procedure has been confirmed for this element; washing or blowing out the media may damage its structure without obvious external signs.
Q2: Will any 5-micron element provide the same protection?
No. The micron label alone does not state how efficiently an element captures particles at that size. Compare the filtration ratio and its test basis, pressure-drop characteristics and structural rating. Two elements labelled 5 microns can differ in efficiency, usable contamination capacity and suitability for the same circuit.
Q3: Why does a filter warning appear soon after replacement?
First check whether the warning occurs only with cold oil or continues at normal operating temperature. Higher viscosity can increase resistance during startup. A persistent warning can also indicate excessive flow, contamination introduced during servicing, an unsuitable element or an indicator fault.
Use the machine's diagnostic procedure to check the indicator, oil condition and installed part. Do not simply fit a coarser element or bypass the warning; that can change the intended component protection.
Q4: Can I keep using the element if the oil still looks clean?
Clear-looking oil can contain particles too small to see. Follow the service schedule and clogging-indicator instructions; use oil analysis where the equipment maintenance programme requires it.
Send the reference 0060D005BH4HC, required quantity and housing model. Include the oil type, flow and pressure requirements for technical review. Contact TOPEP for a replacement review and quotation.